220260070006M11774IP was removing bolts from the cutting edge of a loader bucket with an impact gun.  The bolt came unseated, and a sharp edge on the bolt lacerated the IP's leg above the knee.  
220260070014M13027Employee stopped their off-road truck to use the onsite porta potty. While standing from the driver's seat to exit, they heard a loud pop in their knee and was unable to bear weight. They sat on the truck steps and eased down. Another employee assisted them to a vehicle and transported them to the ER.
220260070017M12205Employee was welding a bucket on an excavator when a piece of slag broke off and rolled down their company uniform onto their under shirt causing it to catch fire resulting in second degree burns to their left upper arm.
220260080004M13598G5 industrial Services was preparing to install a discharge pipe under the log-washers. The pipe had a ninety-degree elbow on one end that was facing upward while in the air. When the pipe was placed on the ground it rolled to the side, EE misjudged where the ninety-degree elbow would lay down to rest. The pipe landed on the top of EE's foot causing injury.
220260090022M10461Operator not paying attention to surroundings.
220260090030M12736While holding the belt the injured worker re positioned a hand to secure the belt from moving, the worker cutting the belt continued cutting the blade moved & cut the left hand behind the index finger. The injured worker did have their PPE Cut Glove on during the incident.
220260130010M10922Minor back strain from lifting old wear plates that were being removed from a miller lining.
220260130011M11814Use of sledgehammer to remove wear plates inside a mill. Employee missed the wedge, hit wear plate that a small metal piece broke off and punctured employee in right upper leg area.
220260130014M12416EE was performing a drag resocket.  EE experienced a laceration to the distal phalanx of the right-hand little finger when a small chip of metal that was embedded in the sledgehammer's handle cut the glove and finger.  EE received stitches. 
220260130025M13327Annual Audiometric Test Hearing Standard Threshold Shift 4th quarter 7000.2 reported 01/12/2026 Due to this on audiometric test dated 12/08/2025 the retest was not confirmed until the next available appointment 01/06/2026. This will not be on 1st qt reporting 7000.2 for 2026. Employee works at multiple mine and construction sites.
220260140002M13808During preparation for dismantling of motor and gear box on slide gate. Employee didn't follow given instructions and removed all bolts from gearbox. That cause released of stored energy on slide gate and motor with gear box start spinning. Employee got caught by the equipment and started spinning with it. During spinning their head hit the handrail which caused a fatal injury.
220260140004M13107During preparation for dismantling of motor and gearbox on slide gate EE's coworker released all bolts on gearbox which cause spinning of motor and gearbox. Coworker got caught by equipment and started spinning with it. During spinning coworker's body hit employee and caused them bruises on their leg and arm.
220260150010M129874 man crew tearing down scaffold around preheaters. a scaffold upright was caught in grating of catwalk. employee used a ladder to access catwalk, EE's harness D ring caught on railing causing employee to fall forward onto grating. Employee used arms to break EE's fall causing strain to right arm.
220260150020M12596Were replacing a bad sprocket following troubleshooting of a gearbox. Removed the 4 bolts from the mounting plate, chain slipped and motor & gearbox fell. The falling equipment impacted the IW left pinky finger, requiring stitches, antibiotics and light duty.
220260200002M11804Miner was in the process of using a pocketknife to cut EE's food and cut the palm of EE's left hand just below the index finger. This resulted in the Miner receiving three sutures.
220260200012M10572Improper operation of bandsaw causing finger laceration. 
220260200020M13728We were cutting side plates and removing them. EE was guiding the piece to the feeder floor. We had cut several pieces; EE's hands were positioned on the side of the pieces when they were cut. This time EE placed EE's hand underneath (without my knowledge) and the plate pinched EE's finger between it and the feeder. We administered first aid and reported it immediately.
220260200027M11784The injured employee was installing Purlin on the Ren Shaft Hoist House when the Purlin rolled, the employee reached to stop it and was cut on the left arm/wrist above the glove.
220260210001M12416Employee was attempting to adjust bolt alignment fingers on bolter using a hammer, while doing so the employees left hand pinky finger got caught between the hammer and the alignment finger causing a laceration. Employee received 7 stitches.
220260220007M12406Installing Brick at Black river in kiln#1 using a pneumatic brick machine. Labor that was injured had improper hand placement on deck of brick machine. Bricklayers move the brick machine and did not communicate on brick machine adjustment. 
220260220009M13818Ee was picking up a porta band saw. EE grabbed the trigger with EE's right hand and then reached to the blade with left hand. EE didn't realize the safety was not engaged. While picking it up, EE depressed the trigger and activated the saw. The saw blade caught EE's glove, pulling EE's hand into the blade. Ee sustained a cut to EE's left index finger requiring stitches to close.
220260220011M12205Warehouse leadman was assisting move ground engagement tools onto a pallet using a lifting magnet.  When EE released the magnet and stood up, EE lost balance/slipped and fell, resulting in an injury to shoulder and knee.
220260220023M12095Employee suffered a non-work related medical issue causing them to collapse to ground, striking the back of their head on an undetermined object and causing a 1/2 inch laceration requiring one staple to close.
220260220026M11413While moving guard employee pinched left ring finger, causing the nail to come off. The finger was smashed between the guard and the railing.
220260230017M10702Miner was struck on left side of face by an extension for manual jack.
220260260002M13177Employee fell from dozer track while adding hydraulic oil. Employee lost footing and fell to the ground, landing on frozen surface. Conditions contributing to the accident included frozen ground and elevated work position on equipment. Injury resulted in a hip fracture requiring medical treatment and lost work time.
220260260003M12947Operator was emptying a hydrated lime bin. When EE dumped the bin, the material covered EE's feet and up EE's legs. The operator turned to get out of the material and fell face first in a pile of hydrated lime. The hydrated lime mashed around and under EE's safety glasses going into EE's eyes.
220260260016M10942Miner exited work truck to begin drilling.  Slipped and fell on ice/snow following snowfall.  
220260280001M12506Employee was removing cast liners within rawmill for replacement. Using a sledge hammer to loosen the first liner, employee struck corner of liner and a piece fractured and came back and struck employee in the nose causing laceration and broken nose.
220260280015M13838On 1.21.2026 Employee reported soreness in the right bicep that developed over time while performing normal work duties.  Employee noted that on 1.16.2026 EE's shoulder had popped while adding a stick of HWT pipe to a drill string going in.  Employee also noted that EE's shoulders pop on occasionally and thought the pain would stop, as pain increased, employee reported the injury.
220260300019M11233Employee got some dust in their eye while standing outside. Was not performing any work at the time. Had all proper PPE on.
220260350005M10963Employee was using three points of contact to get into the telehandler lift prior to operation. 
220260350015M13307Drill helper removed stuffing box, tube lowered to safety block, pulled overshot off tube, stepped back. The driller ran rods up to release tube from rods. Once the driller ran the rod string up, a piece of slipped core (or core stuck in bit/shoe) fell out of the rod string as rods moved forward, striking the helper in the shin.
220260350016M13548Driver pulled a tarp that wasn't unrolling, felt a pull in EE's left arm. Self-treated injury. On 1/26/26, seen by PA-C, neg x-ray. Referred to ortho in Fbks., AK, MRI 1/29/26, revealed 2 minor muscle tears, placed on Lt-arm restrictions; left for 2-wk vacation. Upon return, EE will follow up with the ortho and may need PT if the injury has not healed.
220260350022M11023EE sustained laceration from metal fragment. Clinic prescribed RX antibiotic as preventative measure. 
220260360009M10802Rock bounced off of a GT205 rock crusher conveyor belt and hit employee in head.
220260370011M13327Removing track adjuster from 349F excavator, removed mounting bolts and let adjuster down onto roller, went to move adjuster to let fall out of frame, adjuster fell and crushed middle finger on right hand between track and adjuster. used pry bar and lift adjuster off of hand, remove glove and found bad laceration to middle finger.
220260370019M12987Upon completing repairs to a 336 excavator, then descending from the machine, left foot touched the ground, the Technician felt a pop in their Left knee.  Pain increased over the next few days, and Technician decided to seek medical attention. All PPE was properly worn at the time of the incident.
220260400008M12195EE was working installing a liner and while positioning EE slipped and fell. There was excess water and mud in the area. EE fell and dropped the liner which caused EE's fracture and laceration to EE's left index finger.
220260400015M10321Employee slipped on ice and fell
220260400016M12365An electrical apprentice was stripping the outer rubber casing of a cable for insertion into an MCC. EE was using a utility knife. The knife slipped off of the work and cut through EE's glove into EE's index finger causing a laceration.
220260400021M11303Water hose nozzle struck employee in chin, chipping 2 teeth, cracking 1 tooth and causing a laceration which required 3 stitches. 
220260400023M10492Loose clothing got caught on rebar causing trip. 
220260400041M12045Mechanic employee was using a 30mm wrench to tighten a jam nut on the drill when the wrench slipped off the nut and struck them in the face causing 2 lacerations on their lip and breaking 3 caps on teeth.
220260410002M11423While changing rollers in an impact zone a roller frame assembly fell smashing employees left thumb causing a laceration requiring 12 sutures.
220260420004M13568Technician has lower left side back pain that radiates to the hip that started after the 993K engine tune-up technician was trying to install the engine turn tool. the technician's body is in a awkward position with head tilted and arms up against the engine block while on a 2 step ladder.  After trying first aid, EE finally went to the clinic on 2-9-26.
220260420009M12365Employee sustained a left shoulder dislocation due from a same level fall in slick muddy conditions from ground warming as the day progressed. Employee did not recognize the change in conditions and slipped and fell onto their shoulder.
220260420016M11093Employee was installing a flange, when chip plate fell, causing the flange to fall, striking EE's left thumb.
220260430002M11464Employee was using a grinder throughout their work shift. Around 3:30PM they notified site safety coordinator about irritation in their right eye.
220260430011M12666The employee tripped and fell off last night around 9:30 PM, EE called to report when EE was back in the El Paso terminal, then EE called the nurse this morning to notify of having some difficulty to breathe. I asked them to please notify the mine due to the injury.
220260430012M13368Bad Air through bore hole caused oxygen deficient atmosphere and small amounts of H2S gas. Crew driving underground jeep lost power, employee then exited the jeep to check the master switch, the employee immediately could not breath, and yelled to the other two, they then grabbed their rescuers and retreated up the NOSS to fresh air. 
220260430013M13849Employee was working on an ore truck at laydown yd, unable to hold a wrench, they briefly removed their gloves, touching the wrench with their hands, felt a short sting but wasn't worried about it. When they came back on for the next shift, they complained their fingers hurt, 3 had blisters. Under investigation, due to personal health diagnosis; did not report this upon occurrence.
220260430015M10642Employee was cleaning up around work area and twisted their knee
220260430019M12616Employee was standing on a 8 inch channel and lost footing and reached up and grabbed what they thought was the structure but was the screen perch they were getting ready to weld and it fell and hit their leg and smashed it between the perch and a support beam.
220260440008M13137Fueler rubbed their right eye 2/6/26 with work gloves on. The discomfort started 2/7/2026 and continued to 2/8/26 and the lower right eyelid became noticeably irritated and tender. Medic described the injury as a chemical eyelid exposure with a possible infected eye duct. The employee was prescribed antibiotics.
220260440010M12325Employee was assembling a smudge pot heater when they felt something  snap in their left hand. They sought medical attention February 11, 2026 and was diagnosed with a sagittal band rupture. Employee is currently on restricted duty.
220260480003M12145Worker was exiting the cooler unit and as EE was climbing out of the unit, EE hit a metal anchor that was on the wall near the exit with EE's left leg. When EE hit the anchor with EE's leg EE received a laceration.
220260480016M13578Boulder was lodged in Jaw Crusher of plant. Plant Operator looked into Jaw to get a better view of the obstruction when the boulder popped hard against an iron plate lining the jaw opening. Injured party was wearing proper eye protection, but what ended up being a sliver of metal went underneath bottom rim of eye protection and become lodged in left eye. 
220260480032M13688Offloading Ammonia Nitrate Solution, the hose was clogged. Employee closed the line to check the hose but there was still pressure in the line. When they unhooked the line the pressure sprayed solution hitting them in the face and entering eyes. They washed their eyes out well onsite but went to an eye doctor to be checked out and they prescribed antibiotic ointment
220260480034M12686Approximately 30 kg rock released from the face near the springline in active underground workings. Rock fell 5-8 feet and impacted the miner's arm against the workbasket handrail. Rock was partially restrained behind overlapping face mesh. Miner sustained arm injury.
220260490006M12967On February 4, 2026, an ACME field employee reported to EE's foreman that EE's right forearm felt strained but did not believe medical attention was needed.  EE later requested medical attention, stating EE's forearm began hurting after using an air hammer for two hours removing excess concrete.
220260490019M13187Employee is currently in the ICU unit. Crew was installing cross beams and noticed beams were to close together. Foreman went back to scaffolding and tied off to back rail, tried to pin and move beam over when structure clip slipped off of chime and employee fell with the beam. Employee was tied off to the structure.
220260500002M13748EE in a seated position had completed grinding and set grinder down. They then placed a hand on the duct next to the grinder that had not completely stopped spinning. As they applied weight to their hand to assist in standing up. The weight caused the grinder to slide toward their hand. The spinning wheel contacted the back of left hand resulting in a burn and laceration.
220260500005M12887Miners were attempting to remove an old pump discharge pipe. The upstream valve had been isolated. While loosening the 4-inch Victaulic fitting, the pipe separated due to tension within the line, causing one of the pipes to swing toward the employee, striking EE in the right lower chest.
220260500011M13287Employee was stemming holes from a skid steer bucket with a shovel. The operator of the skid steer asked the employee to hand them something and as the operator reached to take it EE's elbow bumped the controls causing the bucket to drop. The employee's foot was pinned underneath the bucket and the employee felt a lot of pain.
220260500012M11684EE was attempting to cut a zip tie with a razor knife. Knife was in right hand and EE was holding zip tie with left. The knife slipped and lacerated the EE's left palm.
220260510002M10922TYCO MACHINE EMPLOYEE WAS INSTALLING BELTS ON ROCK CRUSHER AND PINCHED RT HAND PINKY FINGER.
220260510011M10421While prying bar slipped and chipped tooth
220260540010M11103While employee was cleaning up debris in a 90 degree pipe. A rock dislodged and stuck employee on right hand. 
220260540026M11554IP was walking on icy surface at mine site camp with right hand in back pocket,  Slipped and fell backwards landing on ground fracturing left long finger. 
220260560005M12836The injured worker states that EE has right elbow pain. Today, while adjusting the pipe bender with a coworker, EE felt/heard a "pop" in EE's right elbow. There is no appreciable bruising at this time. There is no numbness/tingling into EE's hand or fingers. There are no open wounds
220260560015M11634Employee was stripping/cutting the exterior jacket of the 25kv cable when the insulation removal tool (knife) slipped and cut across the top the left index finger.
220260570007M12806Heavy equipment technician was removing rubber step material from a Caterpillar 992 loader with a razor knife.  The knife slipped and lacerated EE's left palm and pinky finger.  EE was treated at the local clinic and received stitches and was released back to duty the same shift.
220260580003M11223Employee suffered seizure causing EE to fall from standing to the ground. Fracture to the skull was sustained in the fall.
220260610019M11694Employee was loading a rock into the jaw crusher, when a rock was launched out of the bucket and struck them through the windshield of the excavator they were operating.
220260620008M13548After unloading, EE drove to the cleanout to ensure the tubs were empty. Using a sledgehammer to tap the side and vibrate the remaining contents, it rotated in EE's hand, catching EE's glove, twisting EE's left thumb.  EE was fitted with a splint to immobilize the thumb, was referred for a follow-up appt. w/ ortho and released to work w/o restrictions.
220260630001M13778EE preparing to remove rigging from pad eye. EE was lowering hook using overhead crane. EE was detaching the shackle from the pad eye with gloved hands. The chain from the hoist had accumulated above the shackle and became caught on structure above pad eye. The hook from hoist rotated downward, EE's L thumb caught between the hook/housing and shackle. Contusion to thumb pad.
220260630002M13478EE was moving a pallet jack loaded with iron when EE encountered a piece of 1/2 inch by 4 inch plywood covering an expansion joint on the floor. The pallet jack became stuck and as EE pulled hard to get it over the plywood, EE slipped and fell to the floor. EE also noted that there was salt and sand in the area where EE was maneuvering the iron.
220260630016M11945While the employee was cutting unistrut with a handheld band saw the saw unexpectedly shifted and contacted their left index finger resulting in a laceration. The employee received two stitches.
220260630017M13738A haul truck operator was pulling away after being loaded when an excavator bucket contacted the truck tailgate. The excavator operator believed the truck bed might roll over and attempted to stop it with the bucket. The contact jolted the truck operator in the seat, causing lower back pain. The operator was transported to a clinic and diagnosed with a lower back strain.
220260650006M11955Employee was using a grinder with a wire wheel when EE stood up and accidentally hit the trigger of the grinder causing it to kick back and get bound up on EE's left forearm causing a laceration.
220260680002M11534IP descended from an AD30 Haul Truck and stepped on a rock that shifted underneath EE's left foot, causing EE's ankle to roll, and EE fell to the ground.
220260680016M11464After adjusting a load of drill pipe on a telehandler, the operator bent down to pick up their wheel chocks and felt pain in their left shoulder. 
220260690004M13568Another employee was using a maul to strike a metal wedge positioned between two flanges during disassembly work under a tank in the V2 area of the alumina plant. While striking the wedge, a fragment broke off and traveled approximately 15 feet, striking and penetrating the injured employee in the shoulder/neck area while the employee was working nearby.
220260690009M13347EE was opening a box of welding rods using a self-retracting blade box cutter. While cutting the thick protective plastic covering, EE cut in a direction toward self. During the cutting motion, the knife got caught in the plastic, it became free the pulling motion caused a laceration to the middle joint (knuckle) of EE's left thumb.
220260690015M11203Employee moving and sorting material. A metal corner of c channel caused a skin laceration on their left arm bicep area.
220260690017M12826EE was stepping over a small containment wall. They stepped over with left foot and stepped on a grading that was to large for the hole it was covering. It caused the grading to flip and the EE fell into the hole and ripped their pants and cut their right upper knee on the grading.
220260690019M11654An employee was struck by the back end of a Hyster forklift knocking them to the ground, then was struck by the right rear tire pinning the left hip and right foot. 
220260700001M10141Unknown, Death
220260700010M11313While attempting to pull a support shaft out of a grate, the shaft shifted and caught employees hand between the shaft and grating.
220260700013M12706Employee was tasked with installing a vulcanized splice in 17-6 conveyor belt. As part of the assigned task,  employee tripped which caused them to fall forward and strike their mouth against the cooker. Contact resulted in a broken tooth and laceration to employee lip.
220260700021M11524Employee was operating an air hoist when their hand got caught in the chain of the hoist. It smashed is left thumb and index finger causing lacerations.
220260710021M11524Employee dropped phone behind their desk. While moving the desk to retrieve the phone they heard a pop and felt excruciating pain in the right shoulder.
220260720003M10762Finger was caught between two bricks. Employee had a fracture with stitches.
220260750005M11704Employee misplaced EE's foot while descending a ladder and slipped of the rung. EE dropped 3-4 feet and landed on EE's right foot. EE's ankle folded over and sprained it.
220260750006M12786Contract truck driver was loaded at the Agg Plant and while descending the hill to the scales, lost EE's brakes, jumped out of the dump truck receiving facial injuries and the truck continued down the road driverless through two berms before finally coming to rest a third berm.
220260750008M11985While exiting the cab of an articulated haul truck, employee stated EE's knee made contact with the vehicle's driver's side door panel. Employee was treated onsite by EMTs and released back to duty.
220260760010M12887Two MWI employees were moving a 12'L x 6"W x 3/4" Thick steel flat Bar weighing approximately 184 lbs. to a saw horse. Both employees set it down before the injured employee was able to clear EE's right middle finger from getting pinched between the steel flat bar and the steel sawhorse.
220260760018M13007An employee used a knife to open a tuna can during a break. While cutting into the can, the knife slipped off the metal edge and cut across their right thumb, causing a two-inch laceration through their cut-resistant glove. The injury occurred because the employee used an improper tool for the task.
220260770001M11874While grinding there was paint and metal particles that blew into EE's eye, EE was wearing foam lined glasses and also a face shield. Wind from the west 21MPH at the time of the incident.
220260770010M11684Employee was walking down the stairs attempting to remove something from EE's bag and missed the last step, causing EE to fall and injure EE's right elbow and left knee
220260770013M11554Finger caught under crane cable after cable slack was winched taut resulting in a laceration requiring 6 stitches.  Returned to full duty; no restrictions.
220260770014M12736Employee was descending steps between two shaker screens. They missed a step and fell, injuring an ankle. Employee was taken to a clinic, X-ray revealed an ankle avulsion fracture. Seen by ortho the next day, fitted w/ a boot. RTW their next sched day with restricted duty.
220260770020M10311Fracture of thumb with stitches
220260770025M13247Driller assistant was positioning a breakout wrench to break rod joints and inadvertently placed a thumb between the head/cap and piston rod, causing their thumb to get smashed in between the two when actuated. This resulted in a tuft fracture to the tip of thumb as well as a laceration to the thumb that required stitches.
220260780006M12796At 2:43pm on 3/8/2026 both hoists lost power. 12 miners were working in the vent shaft, 7 miners were working in the main shaft. Power was re-established to the vent shaft at 3:31PM. Power was re-established to the main shaft at 3:45. No injuries sustained due to loss of power. 
220260780008M10973At approximately 9:30 am, an electrical component failure caused a power outage at the shaft pad.
220260790001M10832Opened the trailer door latch and the latch was stiff and opened with to much force
220260790004M13778EE was positioned beneath the outlet duct assisting coworker with placement of a stiffener ring onto duct. Two manual chain falls were used to maneuver the ring. Ring weighed about 1000 lbs. Each chain fall was rated for 2200 lbs. A chain fall load chain broke, causing the ring to drop. EE states they felt the stiffener ring brush their forearm before landing on their thumb.
220260790018M11474While performing drilling operations, drill pipe fell and struck the operators right hand causing injury to the right thumb which required surgery.
220260790019M11724Employee was stepping down off of the fan deck of a cooling tower and rolled an ankle. They went to urgent care the following morning and it was determined to be fractured.
220260790022M11223Employee was in the process of cutting vent bag with a razor knife and it slipped striking employee on opposite left hand.
220260790029M13849B crew switching T15. IE directed operator over radio to shove 4 cars to a joint. Operator stoppedshort;couplers misaligned.IE entered red zone without protection, violating CS-4(Red Zone) and CS-27 (Adjusting mismatched coupler with or without a device(SafeTRAX) to line couplers. Used their foot to align couplers. Operator continued shoving; IE foot was caught and pinched between.
220260820024M11333At approximately 05.12am on the 12th March 2026, a mechanic was struck by a drill boom in a surface workshop, causing fatal injuries.
220260890002M10762EE hit EE's left index finger with a hammer while aligning a piece of steel.
220260890003M10882Tumbler shaft slid out of 4" nylon strap. Strap was not greasy and was in choke position
220260890025M10512Shotcrete pipe moved and pinched hand of employee. 
220260890027M13838An OTR technician at a quarry installed two spare tires and a new wheel on a Komatsu WA900 loader. While demounting the scrap tire/wheel in the storage yard, EE removed the O-ring with EE's left hand. Residual pressure caused the bead seat band to spring upward, striking EE's left thumb and index finger. This amputated the tip of EE's left index finger and crushed EE's left thumb.
220260890038M12215EE was talking when EE's coworker struck a column with a broken piece of aluminum handle when EE lifted EE's hand into the swinging area. EE received a laceration to EE's left middle finger, took EE to clinic for stiches.
220260890049M11163Employee was unloading a hose crimping machine and hit EE's left index finger on something and created a laceration.
220260890055M10732Debris and other unnecessary work material were present in the work area.
220260890073M11293At 09:28 hours, we experienced a loss of power from the generator plant, resulting in an immediate power outage at the shaft pad.
220260890074M10983At approximately 12:54 am, an electrical component failure caused a power outage at the shaft pad.
220260890076M13538The crew was pulling the liner down the slope and pulled a little to fast when the liner unraveled and caught speed, they tried to hold it with the forklift, it began to roll down the slope when the slope and the crew on the corners got out of the way, the employee in the middle tried to avoid by jumping and it caught their feet and they slipped down.
220260890085M12686On 02/20/2026 the injured employee was descending down the steps of a Komatsu 475 Wheeled Loader when they slipped and fell injuring their right knee. On 03/25/2026 MRI results revealed they had ruptured their right patellar tendon and was placed on work restrictions.
220260890094M13568IP was transferring process solution (mix of sulfuric acid, dipotassium phosphate, and ammonium sulfate) from one tank to another using a pump and hoses. During transfer a solution splash contacted IP's left eye. First aid eye flushing was administered and IP was transported to medical facility for additional flushing. No permanent damage or impairment. 
220260890098M13027Employee was tailing a core tube out from a ct-20 to pull the sample.  While tailing out the tube, the Kelly hose snagged on the wire line causing slack.  As the tube came up changing the angle releasing the slack, dropping the back side of the tube 1 foot causing a strain on the helper right shoulder
220260900002M11824INSTALLING A VITRIOLIC COUPLING ON A PIPE. WHILE HOLDING THE COUPLING A CO-WORKER WAS SWINGING A HAMMER TO SET THE COUPLING. CO-WORKER MISSED THE COUPLING AND HIT LEFT MIDDLE FINGER.
220260900008M12055While standing near the ore stockpile, the employee stepped on a loose rock, lost their balance, and fell to the ground, resulting in discomfort to their wrist.   The injury was reported on March 17, 2026.
220260910003M13828The miner was working by the conex obtaining a service water pump and motor to install on the dredge. While loading items into the skid steer bucket with two plant employees, the injured miner lost EE's grip and dropped EE's end onto EEs finger, which resulted in a cut to EEs finger. The miner finished work on the dredge. At 10:10 pm the miner left the site to go to the hospital.
220260920002M12856EE first said EE had been experiencing soreness for sometime but no specific event occurred, then EE changed EE's story and now claims EE lost EE's footing a bit while climbing a column, and noticed soreness later that day. However, EE failed to inform anyone until Sunday, March 29th.
220260920003M11704Employee was holding a bull pin with their right/dominant hand and missed, hitting it with a hammer with their left hand and instead hit their right hand with the hammer.
220260920023M11484The associate was drilling through a rubber sheet and the drill bit went through the rubber sheet and contacted EE's hand resulting in a laceration.
220260920046M13297Contractor driver from Midwest Industrial Supply pinched or crushed their right index finger in a ladder they were lowering on their truck. The ladder hinges down after a release of a pin. Right index finger was lacerated from the incident. I was informed by their company that part of their finger was amputated at the hospital.
220260970001M11854Injured employee alleges knee pain when stepping on to grating that was on the ground in a laydown yard. The grating was placed on the ground to prevent slip hazard in muddy conditions.
220260970016M12506Employee was removing a carrier roller and support block from a 336 Caterpillar Machine. To remove the block the employee was using a metal punch and hammer.  When the hammer stuck the punch a shard of metal chipped off striking the employee's chest.
220260970017M12335Two employees were placing a section of steel brattice onto the Shaft 10 auxiliary conveyance. While positioning the brattice to allow the conveyance door to close, the injured employee lifted the material and tore their right bicep.
220260970031M11844While enlarging a hole for an E-Stop using a step bit, the bit snagged an aluminum label plate. The plate spun unexpectedly, resulting in cuts to the operator's thumb and index finger.
220260970033M11193Contractor was puttting beams in clinker cooler when rigging slipped causing beam to slip and and smash EE's left pinky
220260980002M11514UNDER THE SILOS IS A TIGHT SPACE. WAS USING A WALK BEHIND SKID STEER. MOBILITY WAS  LIMITED, OPERATOR WAS GOING IN REVERSE WITH A LIMITED FIELD OF VIEW
220260990018M13578The injured employee was attempting to remove an O-ring seal while repairing a jackleg. The pick that the employee was using to remove the O-ring slipped and punctured the thumb on the employees gloved Left hand. The puncture became infected, incisions were made in the thumb in order to clean the wound, the employee also has been receiving IV antibiotics.
220260990029M12506EE fell down an undetermined amount of stairs below the kiln feed area. The worker received multiple lacerations to head and nose requiring extensive care. Also informed late evening at the ER that there was a crack on one or both sides of vertebrae.
220261030002M12937While lowering ladder in the back of the truck to reach the manway. Driver released the safety pin of the ladder with right hand while holding the top section with their left. Somehow their right hand got caught like a vise between the ladder and its support crushing their right index finger.
220261030020M13698Contractor was assisting repairs of coal mill rollers during outage. When shaft was being lowered onto sawhorse the injured who was assisting the moving of the shaft, pinched their right handed middle finger between the shaft and the sawhorse causing a laceration in their finger.  Contractor Supervisor took the injured to get medical attention.  Receiving 10 sutures.
220261030036M10762Employee unhooked lanyard and fell through roof resulting in fatal injuries.
220261040007M11714Cable pull, picking up cable for refeeding into vault. Cable was being fed into vault and pulled out by hand to get it prepped for next pull into building from this vault.
220261050005M11784The employee was found unresponsive lying next to a light plant that was not running.  The time of the event occurring has an approximate window of 30 minutes prior to discovery.
220261050015M11504EE was working on housekeeping tasks. They bent down to pick up an old roller from a conveyor belt and felt a pain in their right wrist. Strain/Sprain
220261070008M11694While unloading drill steels, a steel fell and the left middle finger was caught between a resting steel and the falling steel, resulting in a laceration to the finger. 
220261070011M12606Employee was rolling up mantos on a leach stockpile, when their right forearm became irritated by the raffinate solution.  The employee wash off arm with 4 bottles of water and reported incident to supervisor.  The employee was taken to clinic to be evaluated.
220261100017M13498Injured employee was using a grinder to remove bolts in a unit. The grinder handle was preventing EE's reach from bolt and EE decided to remove the handle. Without a strong securement handle, the grinder kicked back and made contact with the employee's left middle finger, cutting through a glove. This resulted in a laceration requiring 3 stitches.
220261100021M11754Employee was dehydrated and fell to the ground and experienced shaking for approximately 5 minutes. Dr diagnosis was low electrolytes and potassium. No long term issues noted.
220261100034M13849Employee was underneath an articulated haul truck setting jacks and cribbing. The job site was very muddy and while twisting and grabbing equipment they felt their left knee pop. Called nurse triage, they advised visiting urgent care. Doctor orders from urgent care stated employee needed to be off of the appendage and work until an MRI can be taken. MRI scheduled through work comp.
220261110003M11063Employee badged in through turn style was walking towards bus stepped on a rock fell forward to EE's knees
220261110006M13317Employee was using an oxygen/acetylene torch to heat and shape rebar material. The worker inadvertently tripped over the torch hose, which resulted in a loss of balance. As a result of the trip, the worker unintentionally made contact with the active torch flame, causing a burn to the left wrist, just above the cuff of the glove.
220261130015M12706The injured employee was handling the crosshead hook on the #2 bucket for inspections on the bell line. As the employee was walking backward with the crosshead hook, their right boot caught on a "lip" of the collar doors. This caused the employee's knee to hyperextend. 
220261140008M13438While installing lagging on the head pulley, the pulley was being rotated using the drive belt. During rotation, employee's fingers were positioned too far back on the drive belt and motor pulley and two fingers became pinched between the drive belt and motor pulley, the tension prevented immediate release of the fingers. Drive belt was cut.
220261170004M11023A programming issue resulted in the temporary suspension of all hoisting operations at the Main Shaft.
220261170016M12035Employee was squatting down tying mantos to 4" pipe on a leaching stockpile, when they fell foreword hitting right knee and elbow on rock.  Employee felt pain in both areas and reported it to supervisor.
220261170017M12395Employee found slumped over in haul truck while waiting to load. Unresponsive to radio. No prior symptoms reported. Transported for medical care; later diagnosed with suspected stroke and brain clot. No known work-related cause identified.
220261170023M11003IE was working in the laydown when EE became separated from the Skytrak while it remained in motion.
220261180001M13808EE was assisting spreading a telehandler forks, while they tilted mast down to facilitate tine adjustment, the right tine was moved, after EE began sliding the L tine outward. During this process, the R tine slid back unexpectedly. EE attempted to reposition the R tine w/EE's gloved L hand, EE L middle finger got pinched between tine and mast's lower bar. Skin tear on L finger.
220261180008M12927While installing pipe in the shaft, a small piece of metal entered a worker's right eye, causing irritation and redness. Employee was taken to an optometrist, the debris was removed and the employee was prescribed eye drops. At the time of the incident, the worker was wearing safety glasses.
220261180023M11594While conducting tailings dam safety inspections, the wind increased, causing increasingly dusty conditions, resulting in dust getting into the employee's eye.
220261180031M12987It was sunny and cool conditions. Setting up a conveyor on a new crusher when the legs collapsed.  Employee was struck by conveyor and was pulled out from under it. Right ankle was crushed from the impact of the conveyor. 911 was called and employee was air flighted to Boise, Idaho for treatment. 
220261190005M12375UNCHOKING CONE CRUSHER WITH PRYBAR WHILE CRUSHER WAS RUNNING. PRYBAR STRUCK CONE CAUSING IT TO TWIST. INJURED CONTRACT EMPLOYEE SUFFERED TWO LACERATIONS TO RIGHT HAND. INJURED CONTRACT EMPLOYEE WAS NOT WEARING GLOVES AT TIME OF INJURY.  
220261190006M11985After tightening a casing connection, the employee put EE's hands in the derrick before the pipe settled, pinching EE's thumb between the string and the table.   Resulting in a half inch laceration.
220261200012M10932Employee alleges EE stepped off a step and jarred EE's back. No unique conditions associated.
220261240005M13347Jetter hose had a weak area that was not recognized in initial shift inspection. Upon use, the hose burst injuring operator on the left hand. Was treated at local medical center for hand injuries and referred to secondary care at burn center in Augusta. Care was advised to apply ointments and wrap. Return for follow-up in two weeks.
220261240012M11644Employee had machine properly locked out. EE was removing a cover to clear a jam in the machine.  EE dropped the cover on EE's right middle finger causing fracture.
220261240015M13347Operator cut forearm on mast unloading a drill pipe off drill rig. Operator was using improper unloading techniques which resulted in loss of pipe control. This caused operator to be pushed into the mast and cut EE's arm. Operator has since been retrained on proper loading and unloading of drill pipe for Gill Beetle Drill on 4-28-26
220261240017M10902Wrench struck safety glasses, employee suffered laceration to face that required stitches.
220261250003M11413EE looking in Gang Tool Box and the lid unexpectedly closed due to broken shocks and struck EE in the face impacting safety glasses and nose.
220261250011M10752stepped off concrete pad hyperextending left knee, received restricted duty
220261250012M11674While working at the Juniper Pit in Fernley, Nevada on drill D-48, mechanic sustained a dental injury when a wrench slipped and struck EE's tooth during a repair task.
220261250019M13798At approximately 12:35 PM, a fire occurred at the TR Bolinder Crusher. Prior to the incident, maintenance activities were being performed on the guarding for the cone feed, during which a torch was used to clear bolt holes for installation of the guard. Upon completion of the task, three bolinder employees left the work area and returned to their trailer for a scheduled break.
220261260001M10722Removing a rubber liner in valve, right pinky got pinched in the valve. 
220261260002M13428Essentially it came down to the operator of the portable band saw becoming complacent. The trigger was accidentally depressed with right hand while the left hand had came in contact with the blade of the band saw. It was the end of the shift and worker was cleaning up shop. The worker received a total of 6 stitches to the left index finger.
220261260014M10812Employee removed radiator cp on mobile equipment causing minor burn to right hand
220261260025M13728Dust hose to the dust collector pot became full of mud. EE removed the hose at the lower point to  to clear it. The hose fell off. employee continued to unclog the hose by elevating it the middle. EE ended up moving hose off to the side to allow it time to dry out. The next day EE returned to installed it. The employee said EE did not need medical attention till 4-22-26
220261280012M10582Debris entered eye requiring medical treatment to remove. 
220261320022M11724Employee slipped and fell on their left knee while pouring a concrete slab. Injury was diagnosed as a sprain, and the employee was prescribed anti-inflammatory medication. 
220261330001M11043Employee was drilling concrete and cleaning holes to install studs.  Concrete dust got in face and eyes.
220261340001M13798EE and crew were turning a floor brace using a sleever bar in one of the bolt holes. Brace was on flat side. EE standing on E side of the N/S aligned brace pulling on the bar toward EE. In the line of fire when piece reached tipping point where crew needed it for rigging to put in place. Piece reached tipping point, EE lost footing. The sleever bar struck EE's leg causing cut.
220261340002M12606Subcontractor EE was backing out and down the pile with EE's bucket in the raised position. EE's rear passenger tire went off the traveled path and up onto the side of the pole causing the equipment to overturn. Employee exited immediately and was not injured.
220261340003M13698EE and partner were setting up a jig to assist in fit up of the ring to the duct work. EE was holding the piece low to assist in getting the jig welded to the duct. EE's partner stuck EE's weld rod to tack up the piece and rod got stuck. When EE went to remove the rod, the piece fell and landed on EE's pinky fingertip which caused a laceration. EE did have gloves on.
220261340004M12135While moving a skirt that goes on to a conveyor, weighing approx. 150-200 pounds, while on a skate it slid off and pinched left thumb. EE was rushing and did not wait for other staff to secure it before moving it.
220261340006M12446EE was driving out a pin with a hammer for the finish mill hydraulic arm when the pin broke loose causing the punch EE was holding to shift pinching EE's left middle finger against the pin eye edge causing a laceration on EE's left ring finger.
220261340026M12436EE went on the transport bus to place EE's lunch box on a seat before the morning meeting (before start time). EE was exiting the transport bus, as EE stepped off the bus, EE stepped into a divot on the ground.  EE fell to EE's hand and knees.
220261340031M10482Shoulder strain caused by slip into open grating
220261380004M11423Employee was cleaning out the thickener tanks on the south end. While cleaning, employee slipped on mud.  Employee fell and twisted left knee.
220261380018M12476While performing overhead hydro-blasting operations in the hopper area of the scrubber, hardened material adhered to the scrubber wall became dislodged and fell from the scrubber wall. The falling material struck the employee on the left hip area.
220261390021M12516IE was unloading boxes from the tailgate of a pickup truck and carrying them into a Connex storage container. As IE stepped up into the container, EE's foot slipped and EE's right leg came down hard onto the ground causing a sprain to EE's right knee.
220261400019M12215At approximately 7:20PM the shift supervisor was conducting work area inspections, finding a fall of ground in the 3800 ramp. The fall of ground was above the anchorage zone in an active working area that impeded passage.
220261400023M116142 men working close together with knives. ! technician pulled EE's arm back as the other lifted EE's knife striking EE in the arm. EE was cut and needed stitches
220261410001M13838EE was walking on grating that had been installed in slurry bridge. Crew was in the process of lifting the slurry tank agitator gearbox to do a test fit for the millwrights. Piece was overhead, EE was watching the piece and not watching where they were in relation to the open hole. EE stepped off the grating, there is a clip on the beam that EE struck shin on causing cut about 3".
220261410002M11063EE was welding hopper chute standing on belt rollers when EE lost EE's footing and twisted EE's left knee.
220261410008M12436Employee was assisting with core tube retrieval activities at the drill when an issue occurred. During the process of resolving the issue, the employee lost balance and contacted the drill feed frame with EE's hand, resulting in a hand injury.
220261410018M10552Slip lead to sprain of right foot. Restrictions imposed
220261460002M13408While performing geotechnical soil borings for new project driller got EE's tip of the left pointer finger smashed.  Finger was caught in-between the vice and drill rig while attempting to remove pin to open the vice up to pull augers.  Finger needed first aid which was three stiches and driller returned to work after receiving first aid.
220261460007M10892***Reported 5/12/26 - EE claims EE stepped into a hole and experienced a pop in EE's knee
220261460009M13588While a miner was docking the boat in rainy, windy conditions, the motor failed at idle, causing loss of control. Wet, slippery surfaces and an attempt to prevent collision led to a slip and fall, resulting in the miner's right forearm being caught and crushed between the boat and dredge. The miner was assisted and transported to the hospital at - 2:26 AM.
220261460014M11223Miner was attaching lifting apparatus to pipe on the ground to excavator when pipe shifted and caught miner's finger tip. 
220261470010M10502Employee lost control of grinder and cut EE's leg.
220261470012M12887Fabick CAT employee was working in the Cleveland Cliffs Mining Shop. The employee was working on a motor grader cylinder head, installing a fitting. The wrench slipped off and the employee's hand hit a flange, on the cylinder head, causing a small laceration on the top of EE's left hand.
220261470015M13838Employee was directed to retrieve a part from another on-site location. A loader blocked the roadway, requiring travel around it on uneven terrain in a side-by-side. While driving, rough ground caused the vehicle to jerk toward the loader. The employee's left hand, holding the safety handle, was caught in a pinch point during impact, causing an open fracture to the left wrist area
220261480002M11784EE was using Metabo Grinder in an inverted position and cutting against the direction of the blades rotation. the blade  kick backed, causing laceration to the left index finger.
220261480003M12225While cleaning the cement mix tank, the injured employee attempted to clear a plugged drain hole by reaching into the cement mixture. During the process, the employee was exposed to wet cement, resulting in chemical burns.
220261480013M13838Employee was cleaning hardened material from around piping when released material and water caused EE to lose footing and fall into the water. Employee struck the left side of EE's body, head, & left leg/knee on piping & was briefly submerged before being assisted by a coworker. Initial treatment provided by site nurse. Employee was later removed from site pending medical release.
220261480017M11574A contract mechanic/welder hired by another contractor was fatally injured when the ammonium nitrate auger EE was attempting to extract from a pipe exploded.
220261480018M13307Miner was sitting on apron of screen before the Roto-Lift chipping clay out of fins while screen deck was not operating, but still energized. Roto-Lift started turning while miners feet were between fins, causing left leg to become crushed between Roto-Lift fin and frame of screen. EMS was called and miner transported to the ER.
220261490015M13708Employee was assigned to maintenance work on the dredge and was in the process of replacing a cable when a burr on the cable penetrated the employee's impact resistant gloves, resulting in a laceration to the hand. The employee was transported to a medical facility for treatment. The physician administered six stitches and released the employee to return to full duty.
220261490016M12947Passenger in rear of a Mine Cat struck the heater with head (above left ear) and left shoulder when brakes were applied abruptly, causing bruising. Evaluated at local hospital with no paperwork. Seen by physician 5/15/2026, issued light duty; on 5/28/2026 status changed to no work pending MRI.
220261520007M11694employee sustained a laceration to EE's left forearm while performing duct fabrication work while using a 6" grinder to cut duct material from an elevated work position.
220261520011M12646Our employee was performing flight installation on a dryer. While positioning and tack welding a plate, the material became unstable and tipped over, landing on employee's right hand causing amputation to the tip of the 5th finger and a fracture to the 4th finger.
220261520016M13818Employee was assisting with landing a tugger on the 3680 level. Two employees were pulling the tugger on to the level as it was lowered, two employees pulled from one side of the tugger and a third employee was pushing on the opposite side of the tugger. The tugger rolled over in the rigging, trapping and breaking the right arm of the employee between the tugger and the rigging.
220261520018M12876Employee was operating the CAT D9 dozer. When getting out of the cab of the dozer, employee thought the door was in the locker, open position, and it was not.  When EE pulled on the door to get out of the dozer, the door hit EE in the mouth and broke a front, upper tooth at the gumline.
220261520021M13808While offloading a poly-fusion machine from a equipment trailer, the employee lost control on the ramp while pulling it toward themselves. The machine rolled over the employee's right foot. Upon freeing their foot, the employee lost balance but recovered without falling. The employee then grabbed their right buttock, indicating pain, and reported discomfort to another employee.
220261530004M11233Employee was walking up berm near water pump. Felt pop in left leg. Doctor diagnosed as partially ruptured achilles tendon.
220261530009M11133An employee chipped EE's tooth with a leverage tool, while attempting to turn a latch on a parked skid steer box.
220261540010M10772kneeling while wiring a vfd, this building has concert floor, dry and level. 
220261540015M11103Lifting a piece of equipment out of a storage box, it slipped from EE's hand pinching it between another tool.
220261540016M13418While grinding in the RM area, the employee felt a particle in EE's eye; however, EE was wearing proper PPE, including glasses and a face shield. Safety officers removed a small particle from the eye and, to ensure the employee was taken to the clinic, used vibrating tools to remove the rust. The employee returned to work after the clinic.
220261540023M12776Night was clear normal temperatures for evening this time of year. Pit traffic conditions were slow. Helper was 1 week into EE's second hitch with company. Cyclone was clogged; helper tried to use EE's hand to unclog it. Hand was injured by the gate closing inside the cyclone.
220261560003M13668Dozer abruptly stopped on its own causing the operator's upper body to move in a forward while the lap belt held the lower body in the seat. The operator then experienced pain in back with numbness and tingling. Contributing fact was a loose wire at the bottom of the connector and an internal locking tab failure within the connector, allowing the wire to back out.
220261590009M12776Employee was driving a haul truck and stated that EE's lower back was hurting so EE went to personal doctor. On 5/18 EE's MRI was read and was told EE had a bulging disk. Employee was then sent to a Workers Comp. Doctor on 6/3 and was put on restrictions, making it reportable.
220261590014M13187After pulling the inner tube with the latch head, the helper walked to the tube rack. While placing the tube, weight shifted toward the latch head, causing EE to lose balance slightly. EE's right hand lowered, and EE's ring finger was caught under the latch head as it contacted the rack. EE was wearing impact gloves.
220261610001M11584The injured employee tripped over a bolt clamp union that was attached to a pipe in a structure. When EE tripped EE fell on rail striking EE's left side ribs.
220261620005M13778Worker stepped off a bridge while exiting the cooler and landed on a coiled 1.5-inch water hose located at the base of the bridge. Worker's right ankle rolled, resulting in a same-level fall. Worker did not believe first aid was necessary and completed EE's shift. Following day, increased pain in the right ankle led the worker to report the incident to the safety department.
220261620014M11694Employee was carrying a bag of trash and tripped over a drain pipe on the ground, causing EE to fall, resulting in a hairline fracture of the 5th metacarpal of left hand
220261630004M11914Employee was kneeling down on a roof to hold a string line when EE scratched EE's left knee on an exposed screw.  The scratch became infected a few weeks later and required medical attention.
220261660002M13849EE observing installation of catwalk from double drum hoist cab to the mezzanine. Crew was using overhead 15 ton hoist to place the catwalk. Became stuck. As the hoist continued to attempt to move the catwalk, it came free and caused catwalk to spring upward due to stored energy. Panel sprung upward and fell 15' to floor. Struck EE in both knees, puncturing L thigh, needed stitches
220261660004M12255While breaking boulders with excavator and hydraulic hammer a piece of rock came back and hit the boom of the excavator and bounced off hitting the window & breaking it. The broken glass cut the right forearm of the operator.
220261660005M13838EE was in the process of cleaning the shaft of the fan. Crew recognized the hazards of the insulation pins prior to starting work and had bent them down to decrease the potential of sticking themselves. During the cleaning of the fan shaft EE bent elbow to move and caught back of arm/elbow with the pin causing sharp point to impale the tip into skin. Caused a small puncture wound.
220261660006M10642Welding when a piece of slag fell and burned through EE's jeans.
220261660008M10642Bolt keg fell against EE's right inside knee, while being moved.
220261660010M12275EE was coming down stairs which were wet from rain. EE stated EE headed down the stairs and the handrail was wet, EE stepped wrong and rolled EE's ankle. This caused pain to the outside of EE's ankle and to the top of the foot.
220261660035M12646EE was moving a section of 6 inch channel iron that was being used on a conveyor repair. as EE was moving the channel iron EE pinched the tip of EE's right ring finger between the channel and section of handrail. this resulted in sutures on the tip of EE's finger.
220261680014M13528Employee was assisting setting conveyor truss when the truss became hung on a bolt on a chute. Employee placed hands on shims to hold into place when the truss broke free and proceeded to come down mashing EE's fingers resulting in a fracture and sutures on the ring finger of the left hand and a closed fracture on the middle finger of the right hand.
220261680026M12967EE was working in a rail lined bin replacing worn rails. As the EE was installing a new rail, the rail shifted and pinched the tips of the employees right middle finger and right ring finger resulting in a crushing type of injury requiring sutures. there were no fractures and nothing was broken.
220261680027M11804EE was using a utility knife to remove banding from some packaged material. EE was cutting towards self when EE slipped and cut EE's cheek with the knife. this resulted in sutures.
220261690003M12065Employee was backing up pulling vacuum pipe out of sump and EE's foot got caught on vacuum breaker causing EE to loose EE's balance.  EE rotated and landed on EE's right knee as EE was trying to catch self.
220261690014M13628while working on the 3rd floor of rail load-out building, the worker stepped backwards not realizing there was a hole opening in the floor. The worker fell through towards the floor below but caught self and was able to pull self up enough to roll out onto EE's stomach until help arrived. the hatch was left open by another company and not closed prior to work.
220261730029M10802Demo in the preheater and the lime got behind gloves causing irritation to skin 
220261730031M12055While working on bottom of the scaffold deck the employee asked another employee on the scaffold deck above EE for a drill. As the employee looked up to retrieve the tool, EE felt something enter EE's eye.
220261730055M11213Employees were cutting a 4" beam when it accidentally fell on another employee's hand causing injury (fracture)          
220261740003M13347There was very hot temperatures in West Texas on this day. The temperature was 103 degrees at time of the incident. Employees Air conditioner was not properly working throughout the day in the Haul truck. The heat caused the employer to pull over on the side of the haul road, where 30 minutes later EE was found passed out from heat.
220261740015M12095In the process of removing splits and plunger from a core innertube, IE was using a mickey to push the plunger out and struck EE's right hand with the rubber mallet resulting in a cut to the palm of EE's hand.
220261750003M12917EE was attempting to clean a torch tip on an oxygen/acetylene torch. knobs on torch were in the off position and flame was no longer visible. while blowing oxygen and brushing the torch tip with a gloved hand, gas reignited resulting in 1st and 2nd degree burns to the left palm of the hand.
220261760015M11624EE using Drill to drill holes in Metal floor. Drill bit became caught in material causing the drill to twist in the EE hand causing a fractured right ring finger.
220261760018M12546The injured employee was working with another employee to move a valve from one pallet to another. The valve slipped from the grasp of the helper's hand and came down on the injured employees right hand causing a crushing injury to the middle finger tip.
220261770001M13247Individual attempted to dismount forklift via side steps, overstepped the last step causing to fall backwards. Individual attempted to stop impact from fall by extending arm. Left wrist was sprained in the process. Individual was seen by onsite medical team and refused further treatment, as EE didn't feel it was necessary.
220261770011M10882While lifting machine part felt pop in shoulder, received restricted duty 3 days later. 
220261800006M13818Tech was removing a mount plate from a damaged trailer jack stand. The stand sat unsecured on 2 sawhorses requiring stabilization by hand. Using a 4 1/2-in grinder with a cutoff wheel, the wheel moved across a weld, contacting the edge of the material. This caused the grinder to catch and kickback. This force drove the grinder downward into the tech's right thigh above the knee.
220261800017M11073Employee was adjusting the forks on a forklift when they came loose and struck their left arm and left back
220261800024M133372 employees were moving a wire cable reel in preparation to pull cable for a new service when one employee lost balance/footing and fell backwards.  As they fell backwards, they landed on their rights side, mostly on their right elbow.  Employee continued the shift/work as the supervisor and only felt like they bruised their elbow.
220261810013M12215Employee was burned by hot coolant when they were attempting to check fluid levels. Employee was hit in the chest/neck/arms/head with hot coolant. First aid was attempted onsite but determined employee needed to go to ER.
220261820004M10562Tweaked while moving an 18" piece of duct on the ground.
220261820005M11353EE was putting a 3/8" x 4' x 2' piece of steel into the scrap bin when it fell and partially landed on the outside of their right foot.
220261820006M13818EE and a partner were moving 60-80-pound return rollers from the staging area to a cart for transport to the work area. While lowering one roller onto the cart, EE's partner set down their end first which caused the roller to shift and slip from EE's hands. EE's gloved left hand became caught between the return roller and rack resulting in pain and swelling to left index finger.
220261820007M11854EE arrived onsite past check in shack, hit pothole which caused tire to blow. While changing tire, jack slipped out causing the vehicle to fall, pinching a hand between tire and fender.
220261820013M10471Lifting drill rod , felt a "pop" in lower back 
220261820016M10952Employee was pulling cable in upstream area and felt a pop in right shoulder when pulling back.
220261820018M13668While fabricating plates for pan feeder, injured worker (IW) was using an angle grinder to clean and smooth holes that had previously been cut. Piece of metal bypassed worker's face shield and prescription safety glasses and entered the eye. EE was transported to eye clinic for medical evaluation and treatment, where three metal fragments were removed from the eye
220261820019M12456Worker was welding on duct while being fabbed. Overhead, Worker B was grinding. When worker A lifted hood, metal fragment from overhead grinding flew into EE's eye past EE's safety glasses. Worker A was taken to eye clinic, fragment was removed.
220261820021M12786Injured Worker was walking between 2 buses in parking lot prior to work. EE walked out into driveway and was struck by truck going at higher than allowed speed. EE's shin was fractured, ambulance took EE to hospital, and was treated and released for follow up with Orthopedic Dr
220261820030M11023Hand of employee was caught between truck bed and davit arm assembly when loading equipment into bed. 
220261820034M12736Employee was in the process of changing a band saw blade with the assistance of a helper. During the task, the battery was not removed from the tool. While the blade change was underway, another employee inadvertently activated the trigger resulting in laceration to finger
220261820036M12155Employee was carrying scaffolding up stairs to the work area when the scaffolding got caught on a door handle, resulting in tripping. They got a foot caught behind a step before they fell resulting in a knee injury.
220261820039M12496A small rock blocked jammed the conveyor belt on a screening plant. When employee hit the kill button to stop the machine, a large chunk of clay rock fell and hit their RIGHT leg. Sustained fractured Tibia and Fibula and broken bones on top of foot.
220261830001M12095Employee was hooking up input and output lines to a gear pump. Employee started feeling dizzy and briefly lost consciousness. EE was taken to the clinic for evaluation and treated for a personal medical issue.
220261830006M11373Employee was pulling on a roller frame when it came out of the conveyor frame.  It subsequently hit EE in the face, causing a laceration.
220261870006M10812While stemming on the incline, a bucket snapped, felt sharp pain in left shoulder
220261870015M12055While employee was loading a round with a pressurized ANFO pot, the tank ran out of product, causing a surge of pressurized air to flow through the hose. The hose slipped out of their hand and struck them.
220261890029M12947Employee was climbing down a steel ladder, after welding, slipped of the round rung and when they tried to catch themselves they struck their left hand on the ladder. After observation was taken to the clinic for x-ray and they fractured the fifth metacarpal and is pending procedure on 7/14/26
220261900013M12406Contractor equipment transporter was in process of loading and securing front end loader to trailer for off-site transit. Contractor employee reached under the loader to grad a chain on trailer and was caught between the loader and trailer.
220261950030M12957Employee was working near the guard on a tumbler for castle valley stone, as they were hammering their hand got impaled by a sharp piece of the guard. We were not certain of the severity of the injury at the time, however a tendon was severed and they required surgery to fix the injured tendon.
220261960018M11864Mild chemical exposure to face and eye. Employee washed head and eyes with bottled water, then eyewash, then a shower at the office. Antibiotic eye ointment was prescribed. No lost time.
220261970002M13498EE entered a red barricaded area without fall protection on as old equipment was being removed. EE jumped over a floor opening to grab a tagline as the equipment was being lifted. They stepped in the direction on the floor opening and fell through and landed on the first floor. Fall caused a laceration on right cheek and fracture to left shoulder.
220261970018M12756Employee had not been feeling well. Thought they had a cold or bronchitis in April 2026.  Went to a specialist in June 2026.  On 6/19/26 received a diagnosis of silicosis from specialist.  Still waiting for follow up information.  Conditions contributing to this are unknown.
220262040008M13297The forklift was being operated by ESI injured employee, on a dry, compacted 3:1 dirt slope. Forklift was traveling backwards slowly down the slope in a zig-zag movement when front tire came off the ground, causing the equipment to rollover twice. Damage to roll-over cab section.  Operator had seat-belt on at time of roll over.
220262110032M12005Employee dislocated a shoulder and was able to set it back in place. However, after several week, EE complained of ongoing pain. After MRI, it was determined that surgery was required for tendon tear.
220262120009M13458A worker was completing daily fueling and greasing activities on a D6 dozer at the West Diversion Channel. While dismounting the equipment, the worker stepped from the dozer onto the ground and experienced discomfort in their knee. The worker refused medical attention and was provided an icepack, and the incident was classified as a first aid.
220262150007M11834Employee was helping disassemble a Hitachi excavation machine, while hooking up straps to a spreader bar. The bar moved and knocked EE off of the machine. Employee landed on EE's feet
220262220023M12907During jumbo shank replacement, the flushing head was stiff and difficult to seat. Force was applied while the employee's hand remained near the pinch point. The head slipped/shifted unexpectedly, contacting the left middle finger and causing a laceration and fracture requiring one suture.
220265550001M11043A contractor died after a concrete retaining wall collapsed into the excavated trench below crushing EE.
